 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| PRELIMINARY * PERFORMANCE 8.5 - 14.0 GHz Operating Bandwidth 2.6 dB Noise Figure 18 dB Small-Signal Gain 17.5 dm Output Power +6V Single Bias Supply Adjustable Operating Current DC De-coupled Input and Output Ports FMA411 LOW-NOISE X-BAND MMIC * DESCRIPTION AND APPLICATIONS The FMA411 is a 2-stage, reactively matched pHEMT low-noise MMIC amplifier designed for use over the 8.5 to 14.0 GHz bandwidth. The amplifier requires a single +6V supply and one off-chip component for supply de-coupling; the supply voltage can be varied from +3V to +6V if needed. Both the input and output ports are DC de-coupled. Grounding of the amplifier is provided by plated thru-vias to the bottom of the die, no additional ground is required. Operating current can be adjusted using the Source resistor ladders located along the bottom edge, by bonding a particular pad to ground, in order to optimize noise or power performance. Typical applications include low-noise front end amplifiers, and general gain block utilizations in Xband. The amplifier is unconditionally stable over all load states (-45 to +85C), and conditionally stable if the input port is open-circuited. * ELECTRICAL SPECIFICATIONS AT 22C Parameter Operating Frequency Bandwidth Small Signal Gain Saturated Drain Current (see Note) Operating Current Small Signal Gain Flatness Noise Figure 3 -Order Intermodulation Distortion Power at 1dB Compression Input Return Loss Output Return Loss Reverse Isolation rd Symbol BW S21 IDSS IDQ S21 NF IMD P1dB S11 S22 S12 Test Conditions VDD = +6 V IDD 60% IDSS VDD = +3V VDD = +6V VDD = +6 V IDD 60% IDSS VDD = +6 V IDD 60% IDSS VDD = +6 V IDD 60% IDSS POUT = +6 dBm SCL VDD = +6 V IDD 60% IDSS VDD = +6 V IDD 60% IDSS VDD = +6 V IDD 60% IDSS VDD = +6 V IDD 60% IDSS Min 8.5 16.5 210 125 Typ 18 230 140 0.8 2.6 -46 Max 14 21 270 165 1.2 3.5 Units GHz dB mA mA dB dB dBc dBm 16 17.5 -10 -16 -40 -6 -10 -35 dB dB dB * NOTE: Continuous operation at IDSS is not recommended Phone: +1 408 850-5790 Fax: +1 408 850-5766 www.filcs.com Revised: 7/19/04 Email: sales@filcsi.com PRELIMINARY ABSOLUTE MAXIMUM RATINGS1 Parameter Supply Voltage Supply Current RF Input Power Storage Temperature Total Power Dissipation Gain Compression 1 FMA411 LOW-NOISE X-BAND MMIC Symbol VDD IDD PIN TSTG PTOT Comp. 2 2 Test Conditions For any operating current For VDD < 7V For standard bias conditions Non-Operating Storage See De-Rating Note below Under any bias conditions Min Max 8 75% IDSS 0 Units V mA dBm C mW dB -40 150 980 5 Simultaneous Combination of Limits TAmbient = 22C unless otherwise noted 2 or more Max. Limits 80 % Users should avoid exceeding 80% of 2 or more Limits simultaneously Notes: * Operating conditions that exceed the Absolute Maximum Ratings will result in permanent damage to the device. * Total Power Dissipation defined as: PTOT (PDC + PIN) - POUT, where: PDC: DC Bias Power PIN: RF Input Power POUT: RF Output Power * Total Power Dissipation to be de-rated as follows above 22C: PTOT= 0.6 - (0.004W/C) x TCARRIER where TCARRIER = carrier or heatsink temperature above 22C (coefficient of de-rating formula is the Thermal Conductivity) Example: For a 55C carrier temperature: PTOT = 0.6 - (0.004 x (55 - 22)) = 0.47W * For optimum heatsinking eutectic die attach is recommended; conductive epoxy die attach is acceptable with some degradation in thermal de-rating performance (PTOT = 550mW) * Note on Thermal Resistivity: The nominal value of 250C/W is stated for the input stage, which will reach temperature limits before the output stage. The aggregate MMIC thermal resistivity is approximately 175C/W. * HANDLING PRECAUTIONS To avoid damage to the devices care should be exercised during handling. Proper Electrostatic Discharge (ESD) precautions should be observed at all stages of storage, handling, assembly, and testing. These devices should be treated as Class 1A per ESD-STM5.1-1998, Human Body Model. Further information on ESD control measures can be found in MIL-STD-1686 and MIL-HDBK-263. Phone: +1 408 850-5790 Fax: +1 408 850-5766 www.filcs.com Revised: 7/19/04 Email: sales@filcsi.com PRELIMINARY FMA411 LOW-NOISE X-BAND MMIC * MECHANICAL OUTLINE: Notes: 1) All units are in microns, unless otherwise specified. 2) All bond pads are 100x100 m2 3) Bias pad (VDD) size is 100x100 m2 Phone: +1 408 850-5790 Fax: +1 408 850-5766 www.filcs.com Revised: 7/19/04 Email: sales@filcsi.com |
Price & Availability of FMA411
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |